GE IC697PWR711 电源模块

产品描述：
IC697PWR711是Ge Fanuc 90-30系列可编程逻辑控制器(PLC)系列的电源模块。该模块具有可选的输入电压兼容性，如120 VAC和240 VAC，由外部跳线设置决定。对于两种标称vali输入电压，适用的电压范围为90至132 VAC或180至264 VAC，频率为47至63 Hz。

IC697PWR711具有+5VDC、12VDC和-12VDC的输出电源电压以及朝向背板的逻辑电平时序信号。该电源安装在90-30机架的左侧，通过48针背板连接器连接。如果额外机架的总负载不超过IC697PWR711的总100瓦容量，该电源可以为第二个机架供电。具体来说，第二个机架必须小于5.2安培。此外，为第二个机架供电需要使用3英尺长的连接电缆。第二个机架必须在该电缆可及的范围内，因为其设计工作距离不超过3英尺。

具有滑轨式机架安装结构。+5v直流输出18安培，+12v直流输出2安培，从-12v直流输出1安培。该电源具有内部电子短路和过电流保护。对于分支电路熔断，必须安装尺寸合适的外部开关。该电源有一个开/关开关，用于将电源置于活动状态。

该模块采用滑入式机架结构，可在单个电源下进行双机架操作。

GE Fanuc Automation IC697PWR711电源模块在交流电压下运行时，包括电子短路保护和功率因数校正。如果GE Fanuc Automation IC697PWR711电源模块需要在高温和低线电压的环境中连续运行，则必须降低其规格以保证安全运行。正常操作只有在温度低于60摄氏度时才有可能。GE Fanuc Automation IC697PWR711电源模块安装在阿格IC697机架或任何VME积分器机架的左侧插槽中，并且是插入式模块类型。该模块配有3安培的输入半周峰值浪涌电流。

 

IC697PWR711 is the power module of the Ge Fanuc 90-30 series programmable logic controller (PLC) series. This module has optional input voltage compatibility, such as 120 VAC and 240 VAC, determined by external jumper settings. For two nominal input voltages, the applicable voltage range is 90 to 132 VAC or 180 to 264 VAC, with a frequency of 47 to 63 Hz.

IC697PWR711 has output power supply voltages of+5VDC, 12VDC, and -12VDC, as well as logic level timing signals facing the backplane. The power supply is installed on the far left side of the 90-30 rack and connected through a 48 pin backplane connector. If the total load of the additional rack does not exceed the total 100 watt capacity of IC697PWR711, this power supply can power the second rack. Specifically, the second rack must be less than 5.2 amperes. In addition, a 3-foot long connecting cable is required to power the second rack. The second rack must be within the reach of the cable, as its designed working distance does not exceed 3 feet.

Equipped with a sliding rail rack installation structure+ The maximum output of 5V DC is 18 amperes, the maximum output of+12V DC is 2 amperes, and the maximum output of -12V DC is 1 ampere. This power supply has internal electronic short circuit and overcurrent protection. For branch circuit fuses, external switches of appropriate size must be installed. This power supply has an on/off switch that is used to put the power supply in an active state.

This module adopts a sliding in rack structure and can perform dual rack operation under a single power supply.

The GE Fanuc Automation IC697PWR711 power module includes electronic short circuit protection and power factor correction when operating at AC voltage. If the GE Fanuc Automation IC697PWR711 power module needs to operate continuously in high temperature and low line voltage environments, its specifications must be reduced to ensure safe operation. Normal operation is only possible when the temperature is below 60 degrees Celsius. The GE Fanuc Automation IC697PWR711 power module is installed in the left slot of the AG IC697 rack or any VME integrator rack and is a plug-in module type. This module is equipped with a 3-ampere input half cycle peak surge current.